Dynamode USB Wifi Dongle issues

[dvx]

Hi.
So I mastered the drivers - everything works (I used compiled - by sepplmaster » Mon Feb 10, 2014 8:28 pm ).
Great, Thanks.

But I have a new problem
When I set wifi trough "sudo nano /etc/network/interfaces" and reboot or insert wifi dongle to usb my Pi frozen.
I tried several guides.
And tried dongle in windows - works normaly.
Uf...

I have tried:
http://www.howtogeek.com/167425/how-to- ... mand-line/
http://www.suntimebox.com/raspberry-pi- ... ork-setup/
http://learn.adafruit.com/adafruits-ras ... cidentalis

[dvx]

Here is my dmesg, and the end is some ERROR ..?! Can you tell me what it is ?

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.25+ (dc4@dc4-arm-01) (gcc version 4.7.2 20120731 (prerelease) (crosstool-NG linaro-1.13.1+bzr2458 - Linaro GCC 2012.08) ) #622 PREEMPT Fri Jan 3 18:41:00 GMT 2014
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: BCM2708
[ 0.000000] cma: CMA: reserved 16 MiB at 1b000000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 114688
[ 0.000000] free_area_init_node: node 0, pgdat c05cfd6c, node_mem_map c067d000
[ 0.000000] Normal zone: 896 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 114688 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792
[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1278 bcm2708_fb.fbheight=1024 bcm2708.boardrev=0xe bcm2708.serial=0xdd8092ea smsc95xx.macaddr=B8:27:EB:80:92:EA sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p6 rootfstype=ext4 elevator=deadline rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 448MB = 448MB total
[ 0.000000] Memory: 431652k/431652k available, 27100k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdc800000 - 0xff000000 ( 552 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05727b4 (5546 kB)
[ 0.000000] .init : 0xc0573000 - 0xc0597424 ( 146 kB)
[ 0.000000] .data : 0xc0598000 - 0xc05d0870 ( 227 kB)
[ 0.000000] .bss : 0xc05d0870 - 0xc067c3e0 ( 687 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:330
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.001184] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.001252] pid_max: default: 32768 minimum: 301
[ 0.001724] Mount-cache hash table entries: 512
[ 0.002534] Initializing cgroup subsys memory
[ 0.002643] Initializing cgroup subsys devices
[ 0.002685] Initializing cgroup subsys freezer
[ 0.002720] Initializing cgroup subsys blkio
[ 0.002884] CPU: Testing write buffer coherency: ok
[ 0.003364] Setting up static identity map for 0xc0406048 - 0xc04060a4
[ 0.005195] devtmpfs: initialized
[ 0.019658] NET: Registered protocol family 16
[ 0.025639] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.026764] bcm2708.uart_clock = 0
[ 0.028498] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.028553] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.028593] mailbox: Broadcom VideoCore Mailbox driver
[ 0.028695] bcm2708_vcio: mailbox at f200b880
[ 0.028803] bcm_power: Broadcom power driver
[ 0.028845] bcm_power_open() -> 0
[ 0.028874] bcm_power_request(0, 8)
[ 0.529596] bcm_mailbox_read -> 00000080, 0
[ 0.529641] bcm_power_request -> 0
[ 0.529867] Serial: AMBA PL011 UART driver
[ 0.530032] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83) is a PL011 rev3
[ 0.872344] console [ttyAMA0] enabled
[ 0.898290] bio: create slab <bio-0> at 0
[ 0.903616] SCSI subsystem initialized
[ 0.907593] usbcore: registered new interface driver usbfs
[ 0.913315] usbcore: registered new interface driver hub
[ 0.918888] usbcore: registered new device driver usb
[ 0.925486] Switching to clocksource stc
[ 0.929834] FS-Cache: Loaded
[ 0.933010] CacheFiles: Loaded
[ 0.948851] NET: Registered protocol family 2
[ 0.954273] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.961542] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.968069] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.974544] TCP: reno registered
[ 0.977805] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.983715] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.990459] NET: Registered protocol family 1
[ 0.995393] RPC: Registered named UNIX socket transport module.
[ 1.001457] RPC: Registered udp transport module.
[ 1.006184] RPC: Registered tcp transport module.
[ 1.010935] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.018284] bcm2708_dma: DMA manager at f2007000
[ 1.023104] bcm2708_gpio: bcm2708_gpio_probe c05a5e50
[ 1.028560] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB)
[ 1.037947] audit: initializing netlink socket (disabled)
[ 1.043623] type=2000 audit(0.890:1): initialized
[ 1.205918] VFS: Disk quotas dquot_6.5.2
[ 1.210320] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.219158] FS-Cache: Netfs 'nfs' registered for caching
[ 1.225902] NFS: Registering the id_resolver key type
[ 1.231228] Key type id_resolver registered
[ 1.235442] Key type id_legacy registered
[ 1.240236] msgmni has been set to 875
[ 1.246090] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.253949] io scheduler noop registered
[ 1.257913] io scheduler deadline registered (default)
[ 1.263511] io scheduler cfq registered
[ 1.267657] bcm2708_fb_debugfs_init: could not create debugfs entry
[ 1.275252] BCM2708FB: allocated DMA memory 5b400000
[ 1.280410] BCM2708FB: allocated DMA channel 0 @ f2007000
[ 1.309094] Console: switching to colour frame buffer device 159x64
[ 1.326361] uart-pl011 dev:f1: no DMA platform data
[ 1.331444] kgdb: Registered I/O driver kgdboc.
[ 1.336725] vc-cma: Videocore CMA driver
[ 1.340814] vc-cma: vc_cma_base = 0x00000000
[ 1.345609] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 1.351186] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 1.366259] brd: module loaded
[ 1.374868] loop: module loaded
[ 1.378415] vchiq: vchiq_init_state: slot_zero = 0xdb000000, is_master = 0
[ 1.386492] Loading iSCSI transport class v2.0-870.
[ 1.392713] usbcore: registered new interface driver smsc95xx
[ 1.398843] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.604979] Core Release: 2.80a
[ 1.608222] Setting default values for core params
[ 1.613217] Finished setting default values for core params
[ 1.818956] Using Buffer DMA mode
[ 1.822388] Periodic Transfer Interrupt Enhancement - disabled
[ 1.828327] Multiprocessor Interrupt Enhancement - disabled
[ 1.834030] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 1.838477] Dedicated Tx FIFOs mode
[ 1.842644] dwc_otg: Microframe scheduler enabled
[ 1.842888] dwc_otg bcm2708_usb: DWC OTG Controller
[ 1.847923] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 1.855391] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 1.861045] Init: Port Power? op_state=1
[ 1.865046] Init: Power Port (0)
[ 1.868472] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.875442] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.882896] usb usb1: Product: DWC OTG Controller
[ 1.887696] usb usb1: Manufacturer: Linux 3.10.25+ dwc_otg_hcd
[ 1.897635] usb usb1: SerialNumber: bcm2708_usb
[ 1.906981] hub 1-0:1.0: USB hub found
[ 1.914852] hub 1-0:1.0: 1 port detected
[ 1.923189] dwc_otg: FIQ enabled
[ 1.923210] dwc_otg: NAK holdoff enabled
[ 1.923221] dwc_otg: FIQ split fix enabled
[ 1.923242] Module dwc_common_port init
[ 1.923691] usbcore: registered new interface driver usb-storage
[ 1.934204] mousedev: PS/2 mouse device common for all mice
[ 1.944492] bcm2835-cpufreq: min=700000 max=1000000 cur=700000
[ 1.954596] bcm2835-cpufreq: switching to governor powersave
[ 1.964375] bcm2835-cpufreq: switching to governor powersave
[ 1.974051] cpuidle: using governor ladder
[ 1.982120] cpuidle: using governor menu
[ 1.990017] sdhci: Secure Digital Host Controller Interface driver
[ 2.000124] sdhci: Copyright(c) Pierre Ossman
[ 2.008389] sdhci: Enable low-latency mode
[ 2.059530] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platform's DMA
[ 2.071584] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77
[ 2.081688] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.093429] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.110848] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.120426] Indeed it is in host mode hprt0 = 00021501
[ 2.131899] usbcore: registered new interface driver usbhid
[ 2.148320] usbhid: USB HID core driver
[ 2.173243] TCP: cubic registered
[ 2.189507] Initializing XFRM netlink socket
[ 2.197670] NET: Registered protocol family 17
[ 2.229700] Key type dns_resolver registered
[ 2.239752] mmc0: read SD Status register (SSR) after 2 attempts
[ 2.259952] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[ 2.279740] mmc0: new high speed SDHC card at address aaaa
[ 2.290298] registered taskstats version 1
[ 2.302102] mmcblk0: mmc0:aaaa SS08G 7.40 GiB
[ 2.310929] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.324484] mmcblk0: p1 p2 < p5 p6 > p3
[ 2.361808] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[ 2.374278] VFS: Mounted root (ext4 filesystem) on device 179:6.
[ 2.394502] devtmpfs: mounted
[ 2.402210] Freeing unused kernel memory: 144K (c0573000 - c0597000)
[ 2.419591] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.430574] Indeed it is in host mode hprt0 = 00001101
[ 2.640390] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 2.651655] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.664277] hub 1-1:1.0: USB hub found
[ 2.672636] hub 1-1:1.0: 5 ports detected
[ 2.959914] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 3.080299] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 3.101162] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.128798] smsc95xx v1.0.4
[ 3.206060] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:80:92:ea
[ 3.319901] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
[ 3.430688] usb 1-1.3: New USB device found, idVendor=1a40, idProduct=0101
[ 3.459668] usb 1-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.475159] usb 1-1.3: Product: USB 2.0 Hub
[ 3.496721] hub 1-1.3:1.0: USB hub found
[ 3.514007] hub 1-1.3:1.0: 4 ports detected
[ 3.809907] usb 1-1.3.4: new high-speed USB device number 5 using dwc_otg
[ 3.930926] usb 1-1.3.4: New USB device found, idVendor=1a40, idProduct=0101
[ 3.948620] usb 1-1.3.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.960833] usb 1-1.3.4: Product: USB 2.0 Hub
[ 3.980518] hub 1-1.3.4:1.0: USB hub found
[ 3.999671] hub 1-1.3.4:1.0: 4 ports detected
[ 4.108696] udevd[156]: starting version 175
[ 4.289882] usb 1-1.3.4.3: new low-speed USB device number 6 using dwc_otg
[ 4.428097] usb 1-1.3.4.3: New USB device found, idVendor=13ba, idProduct=0018
[ 4.452933] usb 1-1.3.4.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.489648] usb 1-1.3.4.3: Product: Barcode Reader
[ 4.511545] input: Barcode Reader as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4.3/1-1.3.4.3:1.0/input/input0
[ 4.531884] hid-generic 0003:13BA:0018.0001: input,hidraw0: USB HID v1.10 Keyboard [Barcode Reader ] on usb-bcm2708_usb-1.3.4.3/input0
[ 4.576160] input: Barcode Reader as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4.3/1-1.3.4.3:1.1/input/input1
[ 4.634815] hid-generic 0003:13BA:0018.0002: input,hidraw1: USB HID v1.10 Mouse [Barcode Reader ] on usb-bcm2708_usb-1.3.4.3/input1
[ 4.769918] usb 1-1.3.4.4: new low-speed USB device number 7 using dwc_otg
[ 4.917406] usb 1-1.3.4.4: New USB device found, idVendor=0461, idProduct=4d20
[ 4.949705] usb 1-1.3.4.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 4.999642] usb 1-1.3.4.4: Product: USB Optical Mouse
[ 5.031951] input: USB Optical Mouse as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4.4/1-1.3.4.4:1.0/input/input2
[ 5.088869] hid-generic 0003:0461:4D20.0003: input,hidraw2: USB HID v1.11 Mouse [USB Optical Mouse] on usb-bcm2708_usb-1.3.4.4/input0
[ 6.573132] bcm2708-i2s bcm2708-i2s.0: Failed to create debugfs directory
[ 12.431683] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ 12.977174] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ 18.850206] FAT-fs (mmcblk0p5): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 21.965759] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 23.516191] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 25.032689] bcm2835-cpufreq: switching to governor ondemand
[ 25.032724] bcm2835-cpufreq: switching to governor ondemand
[ 27.018327] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:102396k SSFS
[ 43.160518] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 1705.748998] usb 1-1.3.1: new high-speed USB device number 8 using dwc_otg
[ 1705.860981] usb 1-1.3.1: New USB device found, idVendor=148f, idProduct=7601
[ 1705.861016] usb 1-1.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1705.861036] usb 1-1.3.1: Product: 802.11 n WLAN
[ 1705.861054] usb 1-1.3.1: Manufacturer: MediaTek
[ 1705.861072] usb 1-1.3.1: SerialNumber: 1.0
[ 1706.016292] mt7601Usta: module license 'unspecified' taints kernel.
[ 1706.016327] Disabling lock debugging due to kernel taint
[ 1706.047419] rtusb init rtusbSTA --->
[ 1706.048568]
[ 1706.048568]
[ 1706.048568] === pAd = dca74000, size = 860448 ===
[ 1706.048568]
[ 1706.050022] <-- RTMPAllocTxRxRingMemory, Status=0
[ 1706.051554] <-- RTMPAllocAdapterBlock, Status=0
[ 1706.051581] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x8
[ 1706.051594] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x4
[ 1706.051605] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x5
[ 1706.051617] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x6
[ 1706.051630] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x7
[ 1706.051641] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x9
[ 1706.052899] NVM is EFUSE
[ 1706.052922] Endpoint(8) is for In-band Command
[ 1706.052936] Endpoint(4) is for WMM0 AC0
[ 1706.052948] Endpoint(5) is for WMM0 AC1
[ 1706.052959] Endpoint(6) is for WMM0 AC2
[ 1706.052969] Endpoint(7) is for WMM0 AC3
[ 1706.052979] Endpoint(9) is for WMM1 AC0
[ 1706.052989] Endpoint(84) is for Data-In
[ 1706.053001] Endpoint(85) is for Command Rsp
[ 1706.063811] usbcore: registered new interface driver rtusbSTA
[ 1706.267284] FW Version:0.1.00 Build:7640
[ 1706.267312] Build Time:201302052146____
[ 1706.267349] ILM Length = 45380(bytes)
[ 1706.267363] DLM Length = 0(bytes)
[ 1706.285550] Loading FW....
[ 1706.320139] #
[ 1706.344291] RTMP_TimerListAdd: add timer obj dcaf4934!
[ 1706.344324] RTMP_TimerListAdd: add timer obj dcaf494c!
[ 1706.344336] RTMP_TimerListAdd: add timer obj dcaf4964!
[ 1706.344349] RTMP_TimerListAdd: add timer obj dcaf491c!
[ 1706.344363] RTMP_TimerListAdd: add timer obj dcaf48d4!
[ 1706.344373] RTMP_TimerListAdd: add timer obj dcaf48ec!
[ 1706.344386] RTMP_TimerListAdd: add timer obj dca8976c!
[ 1706.344397] RTMP_TimerListAdd: add timer obj dca761e8!
[ 1706.344406] RTMP_TimerListAdd: add timer obj dca76204!
[ 1706.344430] RTMP_TimerListAdd: add timer obj dca897c4!
[ 1706.344445] RTMP_TimerListAdd: add timer obj dca78cf8!
[ 1706.344456] RTMP_TimerListAdd: add timer obj dca783a8!
[ 1706.344476] RTMP_TimerListAdd: add timer obj dca78cdc!
[ 1706.344488] RTMP_TimerListAdd: add timer obj dca78f1c!
[ 1706.344498] RTMP_TimerListAdd: add timer obj dca78d14!
[ 1706.344508] RTMP_TimerListAdd: add timer obj dca78d30!
[ 1706.344518] RTMP_TimerListAdd: add timer obj dca78d4c!
[ 1706.344532] RTMP_TimerListAdd: add timer obj dca8973c!
[ 1706.344574] RTMP_TimerListAdd: add timer obj dca897ac!
[ 1706.344648] RTMP_TimerListAdd: add timer obj dca78f4c!
[ 1706.344660] RTMP_TimerListAdd: add timer obj dca78f64!
[ 1706.344683] RTMP_TimerListAdd: add timer obj dca78f7c!
[ 1706.344695] RTMP_TimerListAdd: add timer obj dca78f94!
[ 1706.373411] cfg_mode=9
[ 1706.373435] wmode_band_equal(): Band Equal!
[ 1706.374212] Key1Str is Invalid key length(0) or Type(0)
[ 1706.374295] Key2Str is Invalid key length(0) or Type(0)
[ 1706.374376] Key3Str is Invalid key length(0) or Type(0)
[ 1706.374459] Key4Str is Invalid key length(0) or Type(0)
[ 1706.376103] 1. Phy Mode = 14
[ 1706.376113] 2. Phy Mode = 14
[ 1706.376124] NVM is Efuse and its size =1d[1e0-1fc]
[ 1706.386910] ERROR!!! MT7601 E2PROM: WRONG VERSION 0xd, should be 12
[ 1706.409175] 3. Phy Mode = 14
[ 1706.409195] AntCfgInit: primary/secondary ant 0/1
[ 1706.620964] ---> InitFrequencyCalibration
[ 1706.620986] InitFrequencyCalibrationMode:Unknow mode = 3
[ 1706.620998] InitFrequencyCalibration: frequency offset in the EEPROM = 83(0x53)
[ 1706.621006] <--- InitFrequencyCalibration
[ 1706.621037] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 1706.624171] MCS Set = ff 00 00 00 01
[ 1706.634818] <==== rt28xx_init, Status=0
[ 1706.635944] 0x1300 = 00064300
[ 1706.635958] RTMPDrvOpen(1):Check if PDMA is idle!
[ 1706.636686] RTMPDrvOpen(2):Check if PDMA is idle!
[ 1706.640136] IOCTL::unknown IOCTL's cmd = 0x00008947
[ 1740.257722] Bulk In Failed. Status=-71, BIIdx=0x6, BIRIdx=0x6, actual_length= 0x0
[ 1740.262618] #
[ 1740.287547] #
[ 1740.298984] #
[ 1740.316272] #
[ 1740.334617] usb 1-1.3: USB disconnect, device number 4
[ 1740.334660] usb 1-1.3.1: USB disconnect, device number 8
[ 1740.335108] rtusb_disconnect: unregister usbnet usb-bcm2708_usb-1.3.1
[ 1740.335133] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 1740.344070] #
[ 1740.344138] #
[ 1740.344169] RTUSB_VendorRequest failed(-1),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x30080542
[ 1740.344186] CMDTHREAD_RESET_BULK_IN: Cannot do bulk in because flags(0x30080542) on !
[ 1740.348734] RTUSB_VendorRequest failed(-1),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1718,pAd->Flags=0x30080542
[ 1740.490252] ---> RTMPFreeTxRxRingMemory
[ 1740.490354] <--- RTMPFreeTxRxRingMemory
[ 1740.490373] reg_atomic get failed(ret=-1)
[ 1740.490712] RTUSB disconnect successfully
[ 1740.491406] usb 1-1.3.4: USB disconnect, device number 5
[ 1740.491440] usb 1-1.3.4.3: USB disconnect, device number 6
[ 1740.670171] usb 1-1.3.4.4: USB disconnect, device number 7
[ 1741.340339] usb 1-1.3: new high-speed USB device number 10 using dwc_otg
[ 1741.441258] usb 1-1.3: New USB device found, idVendor=1a40, idProduct=0101
[ 1741.441294] usb 1-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1741.441316] usb 1-1.3: Product: USB 2.0 Hub
[ 1741.451803] hub 1-1.3:1.0: USB hub found
[ 1741.452121] hub 1-1.3:1.0: 4 ports detected
[ 1741.750272] usb 1-1.3.4: new high-speed USB device number 12 using dwc_otg
[ 1741.851306] usb 1-1.3.4: New USB device found, idVendor=1a40, idProduct=0101
[ 1741.851341] usb 1-1.3.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1741.851361] usb 1-1.3.4: Product: USB 2.0 Hub
[ 1741.852395] hub 1-1.3.4:1.0: USB hub found
[ 1741.852669] hub 1-1.3.4:1.0: 4 ports detected
[ 1742.160317] usb 1-1.3.4.3: new low-speed USB device number 14 using dwc_otg
[ 1742.268653] usb 1-1.3.4.3: New USB device found, idVendor=13ba, idProduct=0018
[ 1742.268692] usb 1-1.3.4.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1742.268712] usb 1-1.3.4.3: Product: Barcode Reader
[ 1742.277946] input: Barcode Reader as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4.3/1-1.3.4.3:1.0/input/input3
[ 1742.281558] hid-generic 0003:13BA:0018.0004: input,hidraw0: USB HID v1.10 Keyboard [Barcode Reader ] on usb-bcm2708_usb-1.3.4.3/input0
[ 1742.295902] input: Barcode Reader as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4.3/1-1.3.4.3:1.1/input/input4
[ 1742.298228] hid-generic 0003:13BA:0018.0005: input,hidraw1: USB HID v1.10 Mouse [Barcode Reader ] on usb-bcm2708_usb-1.3.4.3/input1
[ 1742.390386] usb 1-1.3.4.4: new low-speed USB device number 15 using dwc_otg
[ 1742.497988] usb 1-1.3.4.4: New USB device found, idVendor=0461, idProduct=4d20
[ 1742.498028] usb 1-1.3.4.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1742.498048] usb 1-1.3.4.4: Product: USB Optical Mouse
[ 1742.506792] input: USB Optical Mouse as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4.4/1-1.3.4.4:1.0/input/input5
[ 1742.512060] hid-generic 0003:0461:4D20.0006: input,hidraw2: USB HID v1.11 Mouse [USB Optical Mouse] on usb-bcm2708_usb-1.3.4.4/input0
[ 1757.500781] usb 1-1.3.1: new high-speed USB device number 61 using dwc_otg
[ 1757.612884] usb 1-1.3.1: New USB device found, idVendor=148f, idProduct=7601
[ 1757.612921] usb 1-1.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1757.612942] usb 1-1.3.1: Product: 802.11 n WLAN
[ 1757.612961] usb 1-1.3.1: Manufacturer: MediaTek
[ 1757.612978] usb 1-1.3.1: SerialNumber: 1.0
[ 1757.623539]
[ 1757.623539]
[ 1757.623539] === pAd = dce81000, size = 860448 ===
[ 1757.623539]
[ 1757.623649] <-- RTMPAllocTxRxRingMemory, Status=0
[ 1757.625109] <-- RTMPAllocAdapterBlock, Status=0
[ 1757.625136] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x8
[ 1757.625198] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x4
[ 1757.625213] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x5
[ 1757.625225] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x6
[ 1757.625236] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x7
[ 1757.625248] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x9
[ 1757.633292] NVM is EFUSE
[ 1757.633326] Endpoint(8) is for In-band Command
[ 1757.633342] Endpoint(4) is for WMM0 AC0
[ 1757.633353] Endpoint(5) is for WMM0 AC1
[ 1757.633364] Endpoint(6) is for WMM0 AC2
[ 1757.633375] Endpoint(7) is for WMM0 AC3
[ 1757.633390] Endpoint(9) is for WMM1 AC0
[ 1757.633401] Endpoint(84) is for Data-In
[ 1757.633413] Endpoint(85) is for Command Rsp
[ 1757.899426] FW Version:0.1.00 Build:7640
[ 1757.899456] Build Time:201302052146____
[ 1757.899491] ILM Length = 45380(bytes)
[ 1757.899505] DLM Length = 0(bytes)
[ 1757.917605] Loading FW....
[ 1757.950703] #
[ 1757.968247] RTMP_TimerListAdd: add timer obj dcf01934!
[ 1757.968271] RTMP_TimerListAdd: add timer obj dcf0194c!
[ 1757.968283] RTMP_TimerListAdd: add timer obj dcf01964!
[ 1757.968294] RTMP_TimerListAdd: add timer obj dcf0191c!
[ 1757.968310] RTMP_TimerListAdd: add timer obj dcf018d4!
[ 1757.968320] RTMP_TimerListAdd: add timer obj dcf018ec!
[ 1757.968335] RTMP_TimerListAdd: add timer obj dce9676c!
[ 1757.968344] RTMP_TimerListAdd: add timer obj dce831e8!
[ 1757.968354] RTMP_TimerListAdd: add timer obj dce83204!
[ 1757.968364] RTMP_TimerListAdd: add timer obj dce967c4!
[ 1757.968375] RTMP_TimerListAdd: add timer obj dce85cf8!
[ 1757.968385] RTMP_TimerListAdd: add timer obj dce853a8!
[ 1757.968396] RTMP_TimerListAdd: add timer obj dce85cdc!
[ 1757.968406] RTMP_TimerListAdd: add timer obj dce85f1c!
[ 1757.968416] RTMP_TimerListAdd: add timer obj dce85d14!
[ 1757.968426] RTMP_TimerListAdd: add timer obj dce85d30!
[ 1757.968437] RTMP_TimerListAdd: add timer obj dce85d4c!
[ 1757.968451] RTMP_TimerListAdd: add timer obj dce9673c!
[ 1757.968466] RTMP_TimerListAdd: add timer obj dce967ac!
[ 1757.968538] RTMP_TimerListAdd: add timer obj dce85f4c!
[ 1757.968549] RTMP_TimerListAdd: add timer obj dce85f64!
[ 1757.968561] RTMP_TimerListAdd: add timer obj dce85f7c!
[ 1757.968571] RTMP_TimerListAdd: add timer obj dce85f94!
[ 1757.990149] cfg_mode=9
[ 1757.990174] wmode_band_equal(): Band Equal!
[ 1757.991676] Key1Str is Invalid key length(0) or Type(0)
[ 1757.991767] Key2Str is Invalid key length(0) or Type(0)
[ 1757.991850] Key3Str is Invalid key length(0) or Type(0)
[ 1757.991933] Key4Str is Invalid key length(0) or Type(0)
[ 1757.993643] 1. Phy Mode = 14
[ 1757.993655] 2. Phy Mode = 14
[ 1757.993665] NVM is Efuse and its size =1d[1e0-1fc]
[ 1758.007300] ERROR!!! MT7601 E2PROM: WRONG VERSION 0xd, should be 12
[ 1758.028570] 3. Phy Mode = 14
[ 1758.028590] AntCfgInit: primary/secondary ant 0/1
[ 1758.240474] ---> InitFrequencyCalibration
[ 1758.240496] InitFrequencyCalibrationMode:Unknow mode = 3
[ 1758.240509] InitFrequencyCalibration: frequency offset in the EEPROM = 83(0x53)
[ 1758.240516] <--- InitFrequencyCalibration
[ 1758.240546] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 1758.244948] MCS Set = ff 00 00 00 01
[ 1758.255349] <==== rt28xx_init, Status=0
[ 1758.256454] 0x1300 = 00064300
[ 1758.256469] RTMPDrvOpen(1):Check if PDMA is idle!
[ 1758.257158] RTMPDrvOpen(2):Check if PDMA is idle!
[ 1758.258495] IOCTL::unknown IOCTL's cmd = 0x00008947

[ilovemipi]

Is anyone able to outline how I would create the drivers for an aufs system? It is created with Berryboot.

uname -a gives:

Code: Select all

Linux raspberrypi 3.6.11-rpi-aufs #1 PREEMPT Sat Sep 7 23:10:27 CEST 2013 armv6l GNU/Linux

I followed most of the instructions in this thread without realising I have aufs.

First error I got was with wget http://github.com/raspberrypi/firmware/ ... le.symvers
Came back with a TLS warning alert, unable to establish SSL connection. Tried 4 or 5 times but same error each time.

I pressed on without the Module.symvers but at 'make all' it comes up with:

Code: Select all

root@raspberrypi:~/src/DPA_MT7601U_LinuxSTA_3.0.0.3_20130717_LS# make all
make -C UTIL/ osutil
make[1]: Entering directory `/root/src/DPA_MT7601U_LinuxSTA_3.0.0.3_20130717_LS/UTIL'
cp -f os/linux/Makefile.6.util /root/src/DPA_MT7601U_LinuxSTA_3.0.0.3_20130717_LS/UTIL/os/linux/Makefile
make -C /lib/modules/3.6.11-rpi-aufs/build SUBDIRS=/root/src/DPA_MT7601U_LinuxSTA_3.0.0.3_20130717_LS/UTIL/os/linux modules
make[2]: Entering directory `/lib/modules/3.6.11-rpi-aufs/build'
make[2]: *** No rule to make target `modules'.  Stop.
make[2]: Leaving directory `/lib/modules/3.6.11-rpi-aufs/build'
make[1]: *** [osutil] Error 2
make[1]: Leaving directory `/root/src/DPA_MT7601U_LinuxSTA_3.0.0.3_20130717_LS/UTIL'
make: *** [all] Error 2

Any idea what I need to do to get the drivers working?

[sepplmaster]

The Module.symvers is one of the most important files in the process, it contains information about the modules used in this particular kernel. Therefore it is very important (and tricky) to get the right version of the Module.symvers for your kernel. I have no idea where you can get the one for you, but it has to match your exact kernel.

Concerning the ssl mistake in wget, that is an easy fix, and a quick internet search should have brought you the solution right away:

Code: Select all

wget --no-check-certificate URL

I do not know what causes the problem, so this is just a quick and dirty fix, I guess you loose your advantages of ssl here.

EDIT: You might find your Module.symvers here http://www.raspberrypi.org/forums/viewt ... 66&t=41027

[ilovemipi]

The Module.symvers is one of the most important files in the process, it contains information about the modules used in this particular kernel. Therefore it is very important (and tricky) to get the right version of the Module.symvers for your kernel. I have no idea where you can get the one for you, but it has to match your exact kernel.

Concerning the ssl mistake in wget, that is an easy fix, and a quick internet search should have brought you the solution right away:

Code: Select all

wget --no-check-certificate URL

I do not know what causes the problem, so this is just a quick and dirty fix, I guess you loose your advantages of ssl here.

EDIT: You might find your Module.symvers here http://www.raspberrypi.org/forums/viewt ... 66&t=41027

Thanks for the pointers. --no-check-certificate doesn't currently work, possibly as a Heartbleed OpenSSL precaution. Tried the link for compiling modules with 3.6.11-rpi-aufs but not really enough details for a novice like me to follow.

[ilovemipi]

Apologies sepplmaster --no-check-certificate does work. I had missed sudo bash or sudo from the command.

Moved to Raspbian rather than try to sort out the Berryboot kernel.

After a couple of days I now have the drivers for the latest Raspbian kernel (3.10.37+). All looks ok but it does state kernel is tainted because the module license for mt7601usta is unspecified. I forgot to reduce the syslog output before compiling the drivers and the other option of iwpriv ra0 set Debug=0 currently gives:

Interface doesn't accept private ioctl...
set (8BE2): Operation not permitted


Interface ra0 now appears with ifconfig -a as:

eth0 Link encap:Ethernet HWaddr b8:27:eb:31:16:01
inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:374 errors:0 dropped:0 overruns:0 frame:0
TX packets:319 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:29571 (28.8 KiB) TX bytes:61021 (59.5 KiB)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

ra0 Link encap:Ethernet HWaddr 00:22:c0:98:80:95
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:30478 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5814533 (5.5 MiB) TX bytes:0 (0.0 B)

Now trying to set up ra0 but the Pi fails to boot if I add the following to my EXISTING /etc/network/interfaces:

auto ra0
allow-hotplug ra0
iface ra0 inet dhcp
wpa-ssid "NETWORK SSID"
wpa-psk "NETWORK PASSWORD"

I will try with a fresh /etc/network/interfaces file but in the meantime does anyone know how to get ra0 up an running?

If the drivers seem to work ok I can make them available if anyone wants them (3.10.37+)

[ilovemipi]

Pi still fails to boot with /etc/network/interfaces simply as:

auto ra0
allow-hotplug ra0
iface ra0 inet dhcp
wpa-ssid "NETWORK SSID"
wpa-psk "NETWORK PASSWORD"

I will try renaming the ra0 to wlan0 in udev rules to see if this helps.

[ilovemipi]

iwconfig gives:

ra0 Ralink STA ESSID:"11n-AP" Nickname:"MT7601STA"
Mode:Auto Frequency=2.412 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s
RTS thr:off Fragment thr:off
Link Quality=10/100 Signal level:0 dBm Noise level:0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

lo no wireless extensions.

eth0 no wireless extensions.

This is promising but even when I add Wicd I can't find any way of associating ra0 with my access point. Wicd fails to open.
Any ideas how to finally get this WiFi adapter running?

Wicd is now running but it states there are no wireless networks i.e. it is failing to recognise ra0.

[ozgurakman]

hi I have ralink wifi dongle but it's device id is 148f:760b, not 148f:7601 so it not works athough I did nearly everything. What should I do?

[dvx]

Hi.
After several attempts I managed to run wifi without freezing Pi. I noticed I do not have any ESSID and Mac.
Why?

• ifconfig -a : ra0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
  iwconfig : ra0 Ralink STA ESSID: ""
  
  lsusb : Bus 001 Device 124: ID 148f:7601 Ralink Technology, Corp.

[ilovemipi]

Hi.
After several attempts I managed to run wifi without freezing Pi. I noticed I do not have any ESSID and Mac.
Why?

• ifconfig -a : ra0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
  iwconfig : ra0 Ralink STA ESSID: ""
  
  lsusb : Bus 001 Device 124: ID 148f:7601 Ralink Technology, Corp.

can you please provide the details of uname -a

[dvx]

can you please provide the details of uname -a

• $ uname -a
  Linux raspberrypi 3.10.25+ #622 PREEMPT Fri Jan 3 18:41:00 GMT 2014 armv6l GNU/Linux

I used http://www.raspberrypi.org/forums/viewt ... 67#p503567

[xEIGHTYSIx]

Thanks for the guide. I got my MT7601 wifi adapter working (not Dynamode).

1. Downloaded v3.0.0.4 driver from Mediatek
2. Compiled and installed driver (I had errors during compilation but was able to sort it out.)
3. ra0 appeared in ifconfig, updated /etc/network/interfaces to include ra0 (copied format of wlan0)
4. Installed wicd-curses, updated Preference to use ra0 as wireless network.
5. Wifi signals were detected. Selected desired wifi AP. Input settings for the AP.
6. Connect!

Well, this is just a summary.

[ilovemipi]

Thanks for the guide. I got my MT7601 wifi adapter working (not Dynamode).

1. Downloaded v3.0.0.4 driver from Mediatek
2. Compiled and installed driver (I had errors during compilation but was able to sort it out.)
3. ra0 appeared in ifconfig, updated /etc/network/interfaces to include ra0 (copied format of wlan0)
4. Installed wicd-curses, updated Preference to use ra0 as wireless network.
5. Wifi signals were detected. Selected desired wifi AP. Input settings for the AP.
6. Connect!

Well, this is just a summary.

Are you able to provide the working compiled drivers and which distribution version (3.10.24+, 3.10.25+, 3.10.36+, 3.10.37+) the drivers relate to?

[dvx]

Hi all.
I am still trying compile my own drivers. But when I reaches the point "make mrproper" problems begin.
Does anyone know why? Thanks.

Code: Select all

pi@raspberrypi ~/src/kernel/linux-rpi-3.10.y $ [b]make mrproper[/b]
Makefile:323: /home/pi/src/kernel/linux-rpi-3.10.y/scripts/Kbuild.include: No such file or directory
/bin/bash: /home/pi/src/kernel/linux-rpi-3.10.y/scripts/gcc-goto.sh: No such file or directory
make[1]: scripts/Makefile.clean: No such file or directory
make[1]: *** No rule to make target `scripts/Makefile.clean'.  Stop.
make: *** [_clean_.] Error 2

I want use:

===========================================================

Prepare the kernel/module sources so the driver can build with them.

pi@raspberrypi ~/src/kernel $ sudo ln -s /home/pi/src/kernel/linux-rpi-3.6.y /lib/modules/3.6.11+/build
pi@raspberrypi ~/src/kernel $ cd linux-rpi-3.6.y
pi@raspberrypi ~/src/kernel/linux-rpi-3.6.y $ make mrproper
pi@raspberrypi ~/src/kernel/linux-rpi-3.6.y $ gzip -dc /proc/config.gz > .config
pi@raspberrypi ~/src/kernel/linux-rpi-3.6.y $ make oldconfig
pi@raspberrypi ~/src/kernel/linux-rpi-3.6.y $ make prepare
pi@raspberrypi ~/src/kernel/linux-rpi-3.6.y $ make modules_prepare

[scarrascoh]

After 2 days compiling a lot of things for several rpi versions, I have found the solution. The sources for mt7601 v3.0.0.3 has a bug (at least for me it generated Kernel Panic). I downloaded and compiled sources mt7601 v3.0.0.4 from MediaTek http://www.mediatek.com/en/downloads/mt7601u-usb/. It works fine!

I have uploaded binaries compiled for version 3.10.37+. I have uploaded the full folder compiled here.
https://mega.co.nz/#!lggVkbCZ!oOJiEjDA_ ... 0GT_LZY1Ck
Installation:

Code: Select all

$ tar -vxzf mt7601u_3.0.0.4.tar.gz
$ sudo make install
$ sudo insmod /lib/modules/3.10.37+/kernel/drivers/net/wireless/mt7601Usta.ko
$ sudo reboot

The kernel version must be 3.10.27+ #667. If you don't have it, you can upgrade/downgrade executing the commands:

Code: Select all

$ sudo rpi-update bb7abd7d34e758fc97546620128bf67a45016a5f
$ sudo reboot

And then install drivers.

I have tested it using wpa_supplicant

It worked for me. I hope it could help someone.
Good luck!

P.D: I have used it with TPLink TL-WN727N v4.0

[ilovemipi]

After 2 days compiling a lot of things for several rpi versions, I have found the solution. The sources for mt7601 v3.0.0.3 has a bug (at least for me it generated Kernel Panic). I downloaded and compiled sources mt7601 v3.0.0.4 from MediaTek http://www.mediatek.com/en/downloads/mt7601u-usb/. It works fine!

I have uploaded binaries compiled for version 3.10.37+. I have uploaded the full folder compiled here.
https://mega.co.nz/#!lggVkbCZ!oOJiEjDA_ ... 0GT_LZY1Ck
Installation:

Code: Select all

$ tar -vxzf mt7601u_3.0.0.4.tar.gz
$ sudo make install
$ sudo insmod /lib/modules/3.10.37+/kernel/drivers/net/wireless/mt7601Usta.ko
$ sudo reboot

The kernel version must be 3.10.27+ #667. If you don't have it, you can upgrade/downgrade executing the commands:

Code: Select all

$ sudo rpi-update bb7abd7d34e758fc97546620128bf67a45016a5f
$ sudo reboot

And then install drivers.

I have tested it using wpa_supplicant

It worked for me. I hope it could help someone.
Good luck!

P.D: I have used it with TPLink TL-WN727N v4.0

Thanks for this. I am working through it now. Can you change your reference to 3.10.27 to 3.10.37. I spent 30 minutes 'downgrading' my 3.10.37 to '3.10.27' only to find the hash is for 3.10.37

[ilovemipi]

You are a star scarrascoh.
After a week of trying, upgrading. downgrading and as many kernel panics as you can shake a stick at I have just made my first WEP connection with this WiFi dongle.

I used Wicd and it failed with WPA but I will now review my interfaces file etc and drop Wicd.

I managed to get it running with RaspBMC after 3 or 4 days but I had given up hope of using it with Raspbian. I was prepared to downgrade 10 versions from 3.10.37 to 3.10.27 to give it a go, only to find it is actually for 3.10.37.

Once again, thanks.

[ilovemipi]

I have tested it using wpa_supplicant

It is not accepting my interfaces and wpa_supplicant. Can you share yours and did you manually edit RT2870STA.dat?

[ilovemipi]

I think I have everything running now.
Wicd will connect with WPA2 (AES) as will wpa-gui
Booting up into startx brings up both wlan0 and eth0.

I don't really use startx and I have read that some settings will only give one interface when booting to console. Unpluging the ethernet cable will bring up wlan0 if it didn't come up on boot. Plugging the ethernet cable back in will provide both interfaces and I guess most people will be using eth0 or wlan0, but not both.

Here are my settings.

1. make ra0 appear as wlan0

Code: Select all

sudo nano /etc/udev/rules.d/95-ralink.rules

and copy in the following:
ACTION=="add", SUBSYSTEM=="net", ATTR{type}=="1", KERNEL=="ra*", NAME="wlan0"

2. configure interfaces

Code: Select all

sudo nano /etc/network/interfaces

with the following:
auto lo
iface lo inet loopback
iface eth0 inet dhcp
allow-hotplug wlan0
iface wlan0 inet manual
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
#wireless-power off
iface default inet dhcp
up iwpriv $IFACE set Debug=0

3. Set up wpa_supplicant.conf

Code: Select all

sudo nano /etc/wpa_supplicant/wpa_supplicant.conf

with:
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
ap_scan=1
#update_config=1
network={
ssid="MYPI"
psk="ABABABABAB"

# Protocol type can be: RSN (for WP2) and WPA (for WPA1)
proto=RSN

# Key management type can be: WPA-PSK or WPA-EAP (Pre-Shared or Enterprise)
key_mgmt=WPA-PSK

# Pairwise can be CCMP or TKIP (for WPA2 or WPA1)
pairwise=CCMP

#Authorization option should be OPEN for both WPA1/WPA2 (in less commonly used are SH$
auth_alg=OPEN
}

4. Edit RT2870STA.dat

Code: Select all

sudo nano /etc/Wireless/RT2870STA/RT2870STA.dat

Ensure you have the following entries:
SSID=MYPI
AuthMode=WPAPSK
EncrypType=AES
WPAPSK=ABABABABAB

[connorbp]

Is there a way to install this on kernel version "3.12.18+"??? When I instelled it and then did insmod It gave me an "Invalid module format" error for /lib/modules/3.12.18+/kernel/drivers/net/wireless/mt7601Usta.ko

[ilovemipi]

Is there a way to install this on kernel version "3.12.18+"??? When I instelled it and then did insmod It gave me an "Invalid module format" error for /lib/modules/3.12.18+/kernel/drivers/net/wireless/mt7601Usta.ko

Short answer yes but quite a lot of work unless you are a techy.

Is there anything is 3.12.18+ that you need? It is easy enough to roll back to 3.10.37+ that was the latest release 2 weeks ago.
scarrascoh included details of how to roll back the firmware.

[connorbp]

Is there a way to install this on kernel version "3.12.18+"??? When I instelled it and then did insmod It gave me an "Invalid module format" error for /lib/modules/3.12.18+/kernel/drivers/net/wireless/mt7601Usta.ko

Short answer yes but quite a lot of work unless you are a techy.

Is there anything is 3.12.18+ that you need? It is easy enough to roll back to 3.10.37+ that was the latest release 2 weeks ago.
scarrascoh included details of how to roll back the firmware.

I saw that, but the thing is i want to use rplay with my pi and it suggested using the lastest version. I was thinking about downgrading and seeing if it all works (and doing a backup with dd first just in case) but now my pi is not working because of some glitch that caused my pi's LAN9512 module to stop working when I booted up with my wifi dongle in without using a powered usb hub. I am however going to try and jumpstart it on the weekend and then if all goes well downgrade and install the drivers.

[radonmck]

I seem to be getting a Kernel oops when using the compiled driver form scarrascoh.

I started with a new install off raspbian wheezy and updated to 3.10.37+

I installed the drivers following scarrascoh's instructions but when I plug in the usb wifi adaptor when running or boot with it plugged in I get

kernel BUG at net/core/dev.c@5574!
Internal Error: Oops BUG: 0 [#1] PREEMPT ARM

I can't seem to find any thinking in the log files relating to this so here is a photo of the display

https://dl.dropboxusercontent.com/u/807 ... l_oops.jpg

Anyone got any ideas?

[notacake]

I'm also getting a kernel oops but on 3.12.19 - latest on rpi-update. I adapted all the instructions to use the correct version of the kernel source, so I think it's something that's changed about Linux that the driver doesn't handle.

Here's the relevant section of my log:

Code: Select all

[    6.898105] mt7601Usta: module license 'unspecified' taints kernel.
[    6.906058] Disabling lock debugging due to kernel taint
[    7.411436] rtusb init rtusbSTA --->
[    7.510284]
[    7.510284]
[    7.510284] === pAd = d8ab0000, size = 860448 ===
[    7.510284]
[    7.640774] <-- RTMPAllocTxRxRingMemory, Status=0
[    7.701772] <-- RTMPAllocAdapterBlock, Status=0
[    7.742625] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x8
[    7.797302] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x4
[    7.804072] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x5
[    7.866761] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x6
[    7.907297] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x7
[    7.913964] RTMP_COM_IoctlHandle():pAd->BulkOutEpAddr=0x9
[    7.938038] NVM is EFUSE
[    7.941705] Endpoint(8) is for In-band Command
[    7.947353] Endpoint(4) is for WMM0 AC0
[    7.952257] Endpoint(5) is for WMM0 AC1
[    7.957174] Endpoint(6) is for WMM0 AC2
[    7.961940] Endpoint(7) is for WMM0 AC3
[    7.966614] Endpoint(9) is for WMM1 AC0
[    7.971339] Endpoint(84) is for Data-In
[    7.975948] Endpoint(85) is for Command Rsp
[    7.997467] usbcore: registered new interface driver rtusbSTA
[   20.228846] Unable to handle kernel paging request at virtual address 08bf1fe2
[   20.237673] pgd = c0004000
[   20.241810] [08bf1fe2] *pgd=00000000
[   20.246815] Internal error: Oops: 5 [#1] PREEMPT ARM

Entering kdb (current=0xd738d6a0, pid 1618) Oops: (null)
due to oops @ 0xbf1fbee4

dCPU: 0 PID: 1618 Comm: RtmpMlmeTask Tainted: P           O 3.12.19+ #681
dtask: d738d6a0 ti: d5056000 task.ti: d5056000
PC is at RTUSBBulkOutMLMEPacketComplete+0x8/0x18 [mtnet7601Usta]
LR is at __usb_hcd_giveback_urb+0x60/0x100
pc : [<bf1fbee4>]    lr : [<c02d7828>]    psr: 60000193
sp : d5057d64  ip : 00000000  fp : 00000000
r10: 00000100  r9 : 00000000  r8 : d5056000
r7 : 00000000  r6 : 00000000  r5 : 60000113  r4 : d73f2e00
r3 : 08bf1fde  r2 : 00000fff  r1 : 00000000  r0 : d73f2e00
Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 00c5387d  Table: 15c3c008  DAC: 00000017
dCPU: 0 PID: 1618 Comm: RtmpMlmeTask Tainted: P           O 3.12.19+ #681
[<c00140b4>] (unwind_backtrace+0x0/0xf0) from [<c00112cc>] (show_stack+0x10/0x14)
[<c00112cc>] (show_stack+0x10/0x14) from [<c007e880>] (kdb_dumpregs+0x28/0x50)
[<c007e880>] (kdb_dumpregs+0x28/0x50) from [<c0080af0>] (kdb_main_loop+0x3c0/0x6c0)
[<c0080af0>] (kdb_main_loop+0x3c0/0x6c0) from [<c00831f0>] (kdb_stub+0x154/0x380)
[<c00831f0>] (kdb_stub+0x154/0x380) from [<c007a3ac>] (kgdb_handle_exception+0x340/0x6f0)
[<c007a3ac>] (kgdb_handle_exception+0x340/0x6f0) from [<c0013814>] (kgdb_notify+0x24/0x50)
[<c0013814>] (kgdb_notify+0x24/0x50) from [<c04250e4>] (notifier_call_chain+0x44/0x84)
[<c04250e4>] (notifier_call_chain+0x44/0x84) from [<c042515c>] (__atomic_notifier_call_chain+0x38/0x4c)
[<c042515c>] (__atomic_notifier_call_chain+0x38/0x4c) from [<c0425188>] (atomic_notifier_call_chain+0x18/0x20)
[<c0425188>] (atomic_notifier_call_chain+0x18/0x20) from [<c04251c8>] (notify_die+0x38/0x44)
[<c04251c8>] (notify_die+0x38/0x44) from [<c0011394>] (die+0xc4/0x3b8)
[<c0011394>] (die+0xc4/0x3b8) from [<c041c240>] (__do_kernel_fault.part.9+0x54/0x74)
[<c041c240>] (__do_kernel_fault.part.9+0x54/0x74) from [<c0424df8>] (do_page_fault+0x1f0/0x3f0)
[<c0424df8>] (do_page_fault+0x1f0/0x3f0) from [<c000835c>] (do_DataAbort+0x34/0x98)
[<c000835c>] (do_DataAbort+0x34/0x98) from [<c04235f8>] (__dabt_svc+0x38/0x60)
Exception stack(0xd5057d18 to 0xd5057d60)
7d00:                                                       d73f2e00 00000000
7d20: 00000fff 08bf1fde d73f2e00 60000113 00000000 00000000 d5056000 00000000
7d40: 00000100 00000000 00000000 d5057d64 c02d7828 bf1fbee4 60000193 ffffffff
[<c04235f8>] (__dabt_svc+0x38/0x60) from [<bf1fbee4>] (RTUSBBulkOutMLMEPacketComplete+0x8/0x18 [mtnet7601Usta])
[<bf1fbee4>] (RTUSBBulkOutMLMEPacketComplete+0x8/0x18 [mtnet7601Usta]) from [<bf1fbedc>] (RTUSBBulkOutMLMEPacketComplete+0x0/0x18 [mtnet7601Usta])
[<bf1fbedc>] (RTUSBBulkOutMLMEPacketComplete+0x0/0x18 [mtnet7601Usta]) from [<d7328280>] (0xd7328280)

I'm going to take a brief look over that code to see if there's anything obvious I can see, but I'm not so good at kernel drivers.