Kwjorders
Posts: 19
Joined: Sun Jan 27, 2013 3:22 am

No wireless interfaces found.

Sat Dec 09, 2023 1:43 am

Hello, I have a raspberry pi 4 8GB running rasbian and get the message No Wireless Interfaces Found when attempting to use Wi-Fi. I have it plugged in to an Ethernet Cable and updated to the latest version of bullseye. I have checked the network config in the rasp-config options but only DHCPCD. I have done a few other things too like checking the /etc/network/interfaces file but that was already blank according to the tutorial I was following and that did not help. Looks like this used to be an issue a few years back. Any help would be great.
-Thanks

trejan
Posts: 7098
Joined: Tue Jul 02, 2019 2:28 pm

Re: No wireless interfaces found.

Sat Dec 09, 2023 1:44 am

Show your /boot/config.txt

Kwjorders
Posts: 19
Joined: Sun Jan 27, 2013 3:22 am

Re: No wireless interfaces found.

Sat Dec 09, 2023 7:20 pm

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

# Automatically load overlays for detected cameras
camera_auto_detect=1

# Automatically load overlays for detected DSI displays
display_auto_detect=1

# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2

# Run in 64-bit mode
arm_64bit=1

# Disable compensation for displays with overscan
disable_overscan=1

[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1

[all]

[pi4]
# Run as fast as firmware / board allows
arm_boost=1

[all]

# NOOBS Auto-generated Settings:

Return to “Troubleshooting”